Sharp Home Theater System HT SB40 User Manual

Special Notes  
Important Safety Instructions  
For U.S. customer only  
ENGLISH  
FCC Radiation Exposure Statement  
Electricity is used to perform many useful functions, but it  
can also cause personal injuries and property damage if  
improperly handled. This product has been engineered  
and manufactured with the highest priority on safety.  
However, improper use can result in electric shock and/or  
fire. In order to prevent potential danger, please observe  
the following instructions when installing, operating and  
cleaning the product. To ensure your safety and prolong  
the service life of this product, please read the following  
precautions carefully before use.  
1) Read these instructions.  
2) Keep these instructions.  
3) Heed all warnings.  
4) Follow all instructions.  
5) Do not use this apparatus near water.  
6) Clean only with dry cloth.  
7) Do not block any ventilation openings. Install in  
accordance with the manufacturer’s instructions.  
8) Do not install near any heat sources such as radiators,  
heat registers, stoves, or other apparatus (including  
Amplifiers) that produce heat.  
9) Do not defeat the safety purpose of the polarized or  
grounding-type plug. A polarized plug has two blades  
with one wider than the other. A grounding type plug  
has two blades and a third grounding prong. The wide  
blade or the third prong are provided for your safety. If  
the provided plug does not fit into your outlet, consult  
an electrician for replacement of the obsolete outlet.  
17) Object and Liquid Entry - Never push objects of any kind  
into this product through openings as they may touch  
dangerous voltage points or short-out parts that could  
result in a fire or electric shock.  
This device complies with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. It must not  
be co-located or operating in conjunction with any other  
antenna or transmitter.  
Operation is subject to the following two conditions:  
1. This device may not cause harmful interference, and  
2. This device must accept any interference received,  
including interference that may cause undesired  
operation.  
This equipment should be installed and operated with a  
minimum distance of 20 cm between the radiator and  
person’s body (excluding extremities: hands, wrists, feet  
and ankles.)  
CONSUMER LIMITED WARRANTY  
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the  
"Product"), when ship in its original container, will be free from defective workmanship and materials, and agrees that it will,  
at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent  
at no charge to the purchaser for parts or labor for the period(s) set forth below.  
MHODTEL -SB40  
To prevent fire or shock hazard, do not expose this  
appliance to dripping or splashing. No objects filled with  
liquids, such as vases, shall be placed on the apparatus.  
CAUTION: TO REDUCE THE RISK OF ELECTRIC  
SHOCK, DO NOT REMOVE COVER (OR BACK).  
NO USER-SERVICEABLE PARTS INSIDE. REFER  
SERVICING TO QUALIFIED SERVICE PERSONNEL.  
SOUND BAR HOME THEATER SYSTEM  
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below  
nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or  
other misuse, abnormal service or handling, or which has been altered or modified in design or construction.  
18) Damage Requiring Service - Unplug this product from  
the wall outlet and refer servicing to qualified service  
personnel under the following conditions:  
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide  
proof of purchase to the servicer.  
OPERATION MANUAL  
Explanation of Graphical Symbols:  
a) When the AC cord or plug is damaged,  
b) If liquid has been spilled, or objects have fallen  
into the product,  
The lightning flash with arrowhead symbol,  
within an equilateral triangle, is intended to  
alert the user to the presence of  
uninsulated “dangerous voltage” within the  
product’s enclosure that may be of  
sufficient magnitude to constitute a risk of  
electric shock to persons.  
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law.  
ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE  
LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow  
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.  
Thank you for purchasing this SHARP product. To obtain the best performance from this product, please  
read this manual carefully. It will guide you in operating your SHARP product.  
c) If the product has been exposed to rain or water,  
IC Radiation Exposure Statement (For users in  
Canada)  
d) If the product does not operate normally by  
following the operating instructions. Adjust only  
those controls that are covered by the operating  
instructions as an improper adjustment of other  
controls may result in damage and will often  
require extensive work by a qualified technician to  
restore the product to its normal operation,  
e) If the product has been dropped or damaged in  
any way, and  
f) When the product exhibits a distinct change in  
performance - this indicates a need for service.  
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those  
described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.  
HT-SB40 Sound Bar Home Theater system consisting of HT-SB40 (sound bar system) and CP-SW40 (active  
subwoofer system).  
The radio communications device incorporated into this  
apparatus meets all requirements of the Industry Canada  
Radio Frequency Exposure Rules RSS-210. This Class B  
digital apparatus complies with the Canadian ICES-003  
Class B specifications.  
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and  
exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described  
herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the  
Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.  
In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused  
by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any  
way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion  
of incidental or consequential damages, so the above exclusion may not apply to you.  
The exclamation point within an equilateral  
triangle is intended to alert the user to the  
presence of important operating and  
maintenance (servicing) instructions in the  
literature accompanying the appliance.  
Operation is subject to the following two conditions:  
1. This device may not cause harmful interference, and  
2. This device must accept any interference received,  
including interference that may cause undesired  
operation.  
This equipment should be installed and operated with a  
minimum distance of 20 cm between the radiator and  
person’s body (excluding extremities: hands, wrists, feet  
and ankles.)  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY  
FROM STATE TO STATE.  
WARNING: TO REDUCE THE RISK OF FIRE OR  
ELECTRIC SHOCK, DO NOT EXPOSE THIS  
APPLIANCE TO RAIN OR MOISTURE.  
19) Replacement Parts - When replacement parts are  
required, be sure the service technician has used  
replacement parts specified by the manufacturer or  
have the same characteristics as the original part.  
Unauthorized substitutions may result in fire, electric  
shock, or other hazards.  
20) Safety Check - Upon completion of any service or  
repairs to this product, ask the service technician to  
perform safety checks to determine that the product is  
in proper operating condition.  
21) Wall or ceiling mounting - When mounting the product  
on a wall or ceiling, be sure to install the product  
according to the method recommended by the  
manufacturer.  
22) Power Lines - An outside antenna system should not  
be located in the vicinity of overhead power lines or  
other electric light or power circuits, or where it can fall  
into such power lines or circuits. When installing an  
outside antenna system, extreme care should be  
taken to keep from touching such power lines or  
circuits as contact with them might be fatal.  
Model Specific Section  
Your Product Model Number & Description:  
HT-SB40 Sound Bar Home Theater System  
Note to CATV system installer:  
10) Protect the power cord from being walked on or  
(Be sure to have this information available when you need  
service for your Product.)  
FOR YOUR RECORDS  
This reminder is provided to call the CATV system  
installer’s attention to Article 820 of the National  
Electrical Code that provides guidelines for proper  
grounding and, in particular, specifies that the cable  
ground shall be connected to the grounding system of  
the building, as close to the point of cable entry as  
practical.  
pinched  
particularly  
at  
plugs,  
convenience  
For your assistance in reporting this unit in case of loss  
or theft, please record below the model number and  
serial number which are located on the rear of the unit.  
Please retain this information.  
receptacles, and the point where they exit from the  
apparatus.  
One (1) year parts and labor from the date of purchase.  
Warranty Period for this Product:  
3
D
A
UDIO  
Non-functional accessories, supplies, and consumable  
items.  
Additional Item(s) Excluded from Warranty Coverage  
(if any):  
11) Only use attachments/accessories specified by the  
manufacturer.  
12) Use only with the cart, stand, tripod,  
bracket, or table specified by the  
BLE  
TRE  
BASS  
Model number  
Serial number  
Date of purchase ........................................................  
........................................................  
........................................................  
At a Sharp Authorized Servicer located in the United States.  
To find a location of the nearest Sharp Authorized Servicer,  
call Sharp toll free at 1-800-BE-SHARP.  
Where to Obtain Service:  
Place of purchase ........................................................  
manufacturer, or sold with the apparatus.  
When a cart is used, use caution when  
moving the cart/apparatus combination  
to avoid injury from tip-over.  
What to do to Obtain Service:  
Ship prepaid or carry in your Product to a Sharp Authorized  
Servicer. Be sure to have Proof of Purchase available. If  
you ship the Product, be sure it is insured and packaged  
securely.  
ENERGY STAR® Program Information  
NOTE  
This equipment has been tested and found to comply with  
the limits for a Class B digital device, pursuant to Part 15  
of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses,  
and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause  
harmful interference to radio communications. However,  
there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause  
harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on,  
the user is encouraged to try to correct the interference by  
one or more of the following measures:  
Note:  
Products that have earned  
the ENERGY STAR® are  
designed to protect the  
environment through  
13) Unplug this apparatus during lightning storms or when  
unused for long periods of time.  
This product is recommended for flat panel TV (LED, LCD and plasma).  
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP  
14) Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has been  
damaged in any way, such as power-supply cord or  
plug is damaged, liquid has been spilled or objects  
have fallen into the apparatus, the apparatus has  
been exposed to rain or moisture, does not operate  
normally, or has been dropped.  
SHARP ELECTRONICS CORPORATION  
Accessories  
The following accessories are included.  
Sharp Plaza, Mahwah, New Jersey 07495-1163  
superior energy efficiency.  
23) Protective Attachment Plug - The product is equipped  
with an attachment plug having overload protection.  
This is a safety feature. See Instruction Manual for  
replacement or resetting of protective device. If  
replacement of the plug is required, be sure the  
ENERGY STAR® is a U.S. registered mark.  
IO  
3D  
AUD  
LE  
B
RE  
T
ASS  
B
Additional Safety Information  
Manufactured under license under U.S. Patent Nos:  
service technician has used  
a
replacement plug  
15) Power Sources - This product should be operated  
only from the type of power source indicated on the  
marking label. If you are not sure of the type of power  
supply to your home, consult your product dealer or  
local power company. For product intended to operate  
from battery power, or other sources, refer to the  
operating instructions.  
5,956,674; 5,974,380; 6,487,535  
&
other U.S. and  
specified by the manufacturer that has the same  
overload protection as the original plug.  
worldwide patents issued & pending. DTS, the Symbol,  
DTS and the Symbol together are registered  
Remote Control  
(RRMCGA297AWSA)  
Subwoofer Stand x 2  
(GITAUA022AW01)  
Audio Cable x 1  
HDMI Cable x 1  
(QCNWGA078AWPZ)  
&
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and  
receiver.  
(QCNWGA087AWPZ)  
24) Stand - Do not place the product on an unstable cart,  
stand, tripod or table. Placing the product on an  
unstable base can cause the product to fall, resulting  
in serious personal injuries as well as damage to the  
product. Use only a cart, stand, tripod, bracket or table  
recommended by the manufacturer or sold with the  
product. When mounting the product on a wall, be  
trademarks & DTS Digital Surround and the DTS logos  
are trademarks of DTS, Inc. Product includes software.  
© DTS, Inc. All Rights Reserved.  
Connect the equipment into an outlet on a circuit  
different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV  
technician for help.  
Manufactured under license from Dolby Laboratories.  
Dolby and the double-D symbol are trademarks of Dolby  
Laboratories.  
16) Overloading - Do not overload wall outlets, extension  
cords, or integral convenience receptacles as this can  
result in a risk of fire or electric shock.  
sure to follow the manufacturer  
s instructions. Use  
only the mounting hardware recommended by the  
manufacturer.  
WARNING  
Pattern Paper  
(TCAUHA034AWZZ)  
Quick Start Guide  
(TINSZB421AWZZ)  
HDMI, the HDMI Logo, and High-Definition Multimedia  
Interface are trademarks or registered trademarks of  
HDMI Licensing LLC in the United States and other  
countries.  
FCC Regulations state that any unauthorized changes or  
modifications to this equipment not expressly approved by  
the manufacturer could void the user’s authority to operate  
this equipment.  
Printed in Malaysia  
13A R KI 1  
E-1  
E-2  
E-3  
TINSZB422AWZZ  
Precautions  
Controls and indicators (continued)  
Controls and indicators (continued)  
Sound bar preparation  
In case of an electrical storm, unplug the unit for safety.  
Hold the AC power plug by the head when removing it  
from the AC outlet, as pulling the cord can damage  
internal wires.  
The AC power plug is used as a disconnect device and  
shall always remain readily operable.  
Do not remove the outer cover, as this may result in  
electric shock. Refer internal service to your local  
SHARP service facility.  
This unit should only be used within the range of 41°F -  
95°F (5°C - 35°C).  
Display  
Subwoofer  
Remote Control  
To mount the sound bar on the wall  
Caution:  
General  
Installing the sound bar  
1
Reference page  
1. Remote Control Transmitter . . . . . . . . . . . . . . . . 11  
2. TV ARC Button. . . . . . . . . . . . . . . . . . . . . . . . . 9, 13  
3. Music (Sound Mode) Button. . . . . . . . . . . . . . . . 12  
4. Cinema (Sound Mode) Button . . . . . . . . . . . . . . 12  
5. Sport (Sound Mode) Button . . . . . . . . . . . . . . . . 12  
6. BYPASS Button . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
7. 3D AUDIO Button. . . . . . . . . . . . . . . . . . . . . . . . . 13  
8. APC Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
9. TV Operation Button . . . . . . . . . . . . . . . . . . . . . . 13  
10. AV SYNC Down Button . . . . . . . . . . . . . . . . . . . . 13  
11. Source Button . . . . . . . . . . . . . . . . . . . . . . 9, 10, 13  
12. Subwoofer Level Down Button. . . . . . . . . . . . . . 12  
13. Bass Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
14. On/Stand-by Button. . . . . . . . . . . . . . . . . . . . . . . 11  
15. Game (Sound Mode) Button. . . . . . . . . . . . . . . . 12  
16. News (Sound Mode) Button . . . . . . . . . . . . . . . . 12  
17. Night (Sound Mode) Button . . . . . . . . . . . . . . . . 12  
18. Dimmer Button. . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
19. Demo Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
20. MUTE/Speaker Output Selection  
Please ensure that the equipment is positioned in a  
FRONT VIEW  
REAR VIEW  
1 Tighten the screws and remove the paper. Hook  
the speaker on the screw heads and make sure it  
is properly secured.  
Be very careful to prevent the sound bar [7.27 lbs. (3.3 kg)]  
1
2
well-ventilated area and ensure that there is at least  
4" (10 cm) of free space along the sides, top and back  
of the equipment.  
from falling when mounting on the wall.  
Before mounting, check the wall strength. (Do not put on  
the veneer plaster or whitewashed wall. The sound bar  
may fall.) If unsure, consult a qualified service technician.  
Mounting screws are not supplied. Use appropriate ones.  
Check all wall mount angle screws for looseness.  
Select a good location. If not, accidents may occur or  
the sound bar may get damaged.  
DIGITAL  
14  
2
3
1
4" (10 cm)  
4" (10 cm)  
3
4" (10 cm)  
15  
16  
17  
4
3
DIGITAL  
SHARP is not responsible for damage due to improper  
use. Refer all servicing to a SHARP authorised service  
center.  
SHARP is not responsible for accidents resulting  
5
6
7
from improper installation.  
4" (10 cm)  
4" (10 cm)  
4" (10 cm)  
Driving screws  
2
Warnings:  
Wall  
surface  
18  
19  
20  
AUDIO  
The voltage used must be the same as that specified on  
Reference Page  
SHARP designed the sound bar so you may hang them on  
the wall. Use proper screws (not supplied). See below for  
size and type.  
this unit. Using this product with a higher voltage other  
than that which is specified is dangerous and may  
result in a fire or other type of accident causing  
damage. SHARP will not be held responsible for any  
damage resulting from use of this unit with a voltage  
other than that which is specified.  
1. Dolby Digital Indicator . . . . . . . . . . . . . . . . . . . . . 13  
2. DTS Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
3. Muting Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
8
PA  
IRING  
4
4" (10 cm)  
1/8" (3.2 mm)  
Falling prevention  
AC INPUT  
3/16"  
5
(5 mm)  
3/8" (9 mm)  
7/8" (Min. 22 mm)  
9
In case of repairing, please bring the entire system set  
to the service center.  
Safety wires (not supplied) are useful to prevent the sound  
bar from falling off the table.  
Reference page  
Use the unit on a firm, level surface free from vibration.  
Keep the unit away from direct sunlight, strong  
magnetic fields, excessive dust, humidity and  
electronic/electrical equipment (home computers,  
facsimiles, etc.) which generate electrical noise.  
Do not place anything on top of the unit.  
Do not expose the unit to moisture, to temperatures  
higher than 140°F (60°C) or to extremely low  
temperatures.  
Volume control  
1. Power/Pairing Indicator. . . . . . . . . . . . . . . . . . . . 11  
2. Bass Reflect Duct  
3. Woofer  
4. Pairing button. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
5. AC Power Cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Fixing wall mount angle  
(Horizontal position)  
21  
10  
11  
The sound level at a given volume setting depends on  
speaker efficiency, location and various other factors. It is  
advisable to avoid exposure to high volume levels, which  
occurs while turning the unit on with the volume control  
setting up high, or while continually listening at high  
volumes.  
Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13  
21. AV SYNC Up Button . . . . . . . . . . . . . . . . . . . . . . 13  
22. Volume Up Button . . . . . . . . . . . . . . . . . . . . . . . . 12  
23. Subwoofer Level Up Button . . . . . . . . . . . . . . . . 12  
24. Treble Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
25. Volume Down Button. . . . . . . . . . . . . . . . . . . . . . 12  
1 Fix the pattern paper to the wall in horizontal  
position as below.  
22  
23  
Wall surface  
548 mm  
12  
13  
Sound Bar Rear Panel  
If your system does not work properly, disconnect the  
AC power cord from the AC outlet and replug.  
24  
25  
TV Operation Buttons (Only SHARP TV):  
Pattern paper  
Controls and indicators  
On/Stand-by Sets the TV Input Select Press the  
2 Make a hole on the wall following the screw point  
marks on the pattern paper by using a drill.  
Wall mount set up  
1
2
Button  
power to  
“ON” or  
Button (TV) button to  
switch the  
1-1/4" (32 mm)  
Safety screw  
(not supplied)  
“STAND-BY”.  
input source.  
3/8" (8-9 mm)  
Channel Up Switch up/  
and Down  
Volume Up Turn up/  
Safety wires  
down the TV and Down  
channels.  
down the TV  
volume.  
Wall surface  
Buttons  
Buttons  
3
Fix a wall mount plug (not supplied) into the hole  
using a hammer, until it is flush with the wall surface.  
Wall  
6
5
4
1-1/4" (32 mm)  
Sound bar unit  
Note:  
3/8" (8-9 mm)  
Wall surface  
Desktop set up  
3
2
Some models of SHARP TV may not be operable.  
Sound bar unit  
4 Fix screws into the wall for the speaker, as shown  
in the illustration.  
1
Make sure that the screw and the wall can support a  
load of 20 kg (45 lbs).  
3
4
5
6
7
8
9
10  
Reference page  
1. HDMI OUT (TV ARC) Jack . . . . . . . . . . . . . . . . . . 9  
2. HDMI IN 1 Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
3. HDMI IN 2 Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Reference page  
Fix the screws, so the screw head extends about  
5.5 mm (7/32") from the wall.  
4. Optical IN Jack . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
5. Audio IN Terminal . . . . . . . . . . . . . . . . . . . . . . . . 10  
6. AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Sound Bar Front Panel  
5.5 mm  
(7/32")  
Safety  
screw  
(not  
Safety  
wires  
(not  
Reference page  
Reference page  
Rack/  
table  
1. Left Channel Speakers  
2. Right Channel Speakers  
3. On/Stand-by Button . . . . . . . . . . . . . . . . . . . . 11, 14  
4. SOURCE Button . . . . . . . . . . . . . . . . . . . . . 9, 10, 13  
5. Pairing Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
6. Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . .11  
7. Demo Indicator . . . . . . . . . . . . . . . . . . . . . . . .11, 15  
8. Sound Mode Button . . . . . . . . . . . . . . . . . . . .12, 14  
9. Volume Down Button. . . . . . . . . . . . . . . . . . . . . . .12  
10. Volume Up Button . . . . . . . . . . . . . . . . . . . . . . . . .12  
Safety  
screw  
Wall  
mounting  
Wall surface  
Wall surface  
supplied)  
supplied)  
(not  
supplied)  
screw  
E-4  
E-5  
E-6  
E-7  
System connections (continued)  
Placing the system  
Audio connections to TVs, DVD players, VCRs, etc.  
Remote control  
General control  
HDMI Connection  
Installation image:  
Notes:  
Other connection (without HDMI)  
Battery installation  
The front panel of the sound bar is not removable.  
Caution:  
The transmission distance of the wireless signal between  
the subwoofer and sound bar is about 32 feet (10 m), but  
may vary depending on your operating environment. If a  
steel-concrete or metallic wall is between the subwoofer  
and the sound bar, the system may not operate at all,  
because the wireless signal cannot penetrate metal.  
The illustration below shows the flows of audio and video signals.  
TV  
Use 1 “AA” size battery (UM/SUM-3, R6, HP-7 or  
similar). Batteries are not included.  
Turn off all other equipment before making this connection.  
TV  
The illustration below shows the flows of the signals.  
Audio signal  
Video signal  
DVD/Blu-ray  
Disc Player  
AUDIO  
1 Open the battery cover.  
Audio and Video signal  
2 Insert the batteries according to the direction  
TV  
indicated in the battery compartment.  
DVD/Blu-ray  
Digital tuner  
Caution:  
When inserting or removing the battery, push them  
Do not change the installation direction when the sound  
toward the  
battery terminals.  
bar is turned on.  
3 Close the battery cover.  
Do not stand or sit on the sound bar and subwoofer as  
you may be injured.  
1. Method 1  
This connection is for HDMI TV with ARC (Audio Return Channel).  
Make sure to enable the HDMI CEC when making  
HDMI connection. For details, refer to the operation  
manual of the TV.  
Sound Bar  
Placing the stand  
TV  
DVD, Blu-ray disc  
player or similar  
Digital tuner, etc.  
Place the stand as shown.  
Notes:  
To turn the power on  
Caution:  
Refer to the operation manual of the equipment to be connected.  
Fully insert the plugs to avoid fuzzy pictures or noises.  
Connecting via this method may disable TV internal speakers.  
In some cases, a small background noise could emit from the sound bar, when you use the RCA audio output terminal  
connection from a TV-Set/DVD/Blu-ray Disc Player. In such case, please change the connection to the HDMI/ARC or  
headphone terminal connection. This effect depends on the used TV/DVD/Blu-ray Disc Player-Brand, model and age,  
and it is not a quality matter from the sound bar.  
To HDMI (TV ARC) input  
terminal  
To HDMI output  
terminal  
Remove the battery if the sound bar will not be used for  
a long period of time. This will prevent potential damage  
due to battery leakage.  
DVD player  
Place the system as shown.  
VCR  
Subwoofer  
Press the ON/STAND-BY button on the sound bar or the  
remote control.  
The power turns on and the subwoofer indicator turns  
blue. If the power does not turn on, check whether the  
AC power cord is plugged in properly.  
The system will automatically power on if TV or similar  
component which supports HDMI CEC, is turned on.  
To set the sound bar to stand-by mode:  
Do not use rechargeable battery (nickel-cadmium  
battery, etc.).  
Installing the battery incorrectly may cause the sound  
bar to malfunction.  
Batteries (battery pack or battery installed) shall not be  
exposed to excessive heat such as sunshine, fire or the  
like.  
Remove the protective film covering the sound bar and  
subwoofer before turn on the system.  
Sound Bar  
To HDMI OUT (TV ARC) output terminal  
To HDMI input terminal  
Connecting a TV, or DVD player, etc.  
2. Method 2  
This connection is for HDMI TV without ARC (Audio Return Channel).  
Press the ON/STAND-BY button again on the main unit or  
the remote control and the subwoofer indicator turns red.  
Connect to the TV using an optical digital cable or an audio cable.  
TV  
Notes concerning use:  
To HDMI input terminal  
TV  
Stand  
Replace the battery if the operating distance is reduced  
or if the operation becomes erratic.  
Notes:  
DVD, Blu-ray disc  
player or similar  
A slight audio delay after TV is turned ON does not  
mean that the system is faulty. This is normal.  
“AQUOS speaker is enabled” message will be  
displayed if SHARP LCD TV does not detect HT-SB40  
during power on. However the message “AQUOS audio  
with AQUOS LINK is enabled” will be displayed soon as  
HT-SB40 is detected. These messages may vary for  
other TV model.  
To audio output terminal  
To audio output terminals  
System connections  
Periodically clean the transmitter on the remote control  
and the sensor on the sound bar with a soft cloth.  
Exposing the sensor on the sound bar to strong light  
may interfere with operation. Change the lighting or the  
direction of the sound bar.  
Make sure to unplug the AC power cord before making any connections.  
To HDMI output  
terminal  
To Headphone  
terminal  
To  
Subwoofer  
or  
HEADPHONE  
terminal  
Keep the remote control away from moisture, heat,  
shock, and vibrations.  
Blu-Ray/  
DVD player/Digital  
Tuner  
To optical  
digital audio  
output  
Test of the remote control  
Demonstration mode  
Point the remote control directly at the remote sensor on  
the sound bar.  
The first time the unit is plugged in, the unit will enter  
the demonstration mode.  
To cancel the demonstration mode, press the DEMO  
button on the remote control during power stand-by  
mode.  
To enter to the low power consumption mode, press  
and hold the DEMO button (Demo indicator turns off).  
terminal  
Sound Bar  
To HDMI input terminal  
To HDMI OUT (TV ARC) output terminal  
To select HDMI 1, 2 or TV ARC function (Source):  
Sound Bar  
The remote control can be used within the range  
shown below:  
Optical digital  
audio cable  
(commercially  
available)  
Audio cable  
(commercially  
available)  
Press SOURCE button repeatedly until “HDMI 1”, “HDMI 2” or “TV ARC” appears on the display, or  
press TV ARC button on the remote control to select the TV ARC.  
Remote sensor  
Notes:  
This sound bar supports HDMI which enables ARC (Audio Return Channel).  
To AUDIO IN  
input terminals  
To enable ARC make sure to use High Speed HDMI™ cable (with ARC).  
Connecting the wireless Subwoofer  
AC outlet  
AC 120 V ~ 60 Hz  
To OPTICAL  
IN (optical)  
input terminal  
AC outlet  
AC 120 V ~ 60 Hz  
This ARC feature requires TV that supports ARC. Refer the operation manual of the TV to determine which terminal supports ARC.  
To listen to the sound from a non-ARC-compatible TV, connect the audio output from TV to this system’s. (refer page 10)  
This sound bar can be operated (power on/off or volume up/down) via a TV or similar component which supports HDMI CEC  
(Consumer Electronics Control). If this does not work, it does not mean this system is faulty. Refer to the operation manual of  
the respective component on how to activate the CEC.  
PA  
IRING  
The sound bar and subwoofer will link automatically  
(wirelessly) when turned on as it is already pre-linked at  
the factory. If the link cannot be established, please set the  
connection by the following method.  
1. Press and hold the PAIRING button on the sound bar for  
more than 3 seconds.  
2. Within 2 minutes, press and hold the PAIRING button on  
the subwoofer for more than 3 seconds.  
During pairing process:  
AC INPUT  
8" - 20'  
(0.2 m - 6 m)  
Sound Bar  
Example: Go to the Menu of the component to search and enable the CEC. Different brands may have different naming for the  
CEC. For SHARP LCD TV, it is named as AQUOS LINK.  
15° 15°  
CAUTION:  
CEC is not available during Low power consumption mode.  
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.  
To listen to the sound from this system, you will need to press and hold the (MUTE) button (refer page 13) or adjust  
the speaker output settings within the TV menu.  
For details, refer to the operation manual of the TV.  
Sound bar and Subwoofer connection  
Caution  
Do not allow any objects to fall into or to be placed in the bass reflex duct.  
Do not stand or sit on the sound bar/subwoofer. You may be injured.  
To select OPTICAL function:  
If you are unable to select external speaker setting from the TV menu (E.g. For SHARP LCD TV, it is named as AQUOS  
AUDIO SP), turn the CEC OFF and ON again.  
Press SOURCE button repeatedly until “OPTICALappears on the display.  
On sound bar: PAIRING” will blink.  
On subwoofer: indicator will blink in blue.  
To enjoy 3D images, this system must be connected to a 3D-compatible TV and components (3D BD player, etc.) via High Speed  
HDMI cables. Put on the 3D glasses, otherwise 3D images may not be viewed properly.  
If you want to use HDMI IN 1 jack, please use the supplied HDMI cable.  
To select AUDIO IN function:  
Press SOURCE button repeatedly until “AUDIO IN” appears on the display.  
E-8  
E-9  
E-10  
E-11  
General control (continued)  
Specifications  
Maintenance  
General control (continued)  
Troubleshooting chart  
General control (continued)  
When pairing is successful:  
As part of our policy of continuous improvement, SHARP  
reserves the right to make design and specification changes  
for product improvement without prior notice. The  
performance specification figures indicated are nominal  
values of production unit. There maybe some deviations  
from these values in individual unit.  
Muting  
Many potential problems can be resolved by the owner without  
calling a service technician.  
If something is wrong with this product, check the following  
before calling your authorized SHARP dealer or service center.  
Symptom  
Possible cause  
Cleaning the cabinet  
AV SYNC level control  
On sound bar:  
On subwoofer:  
PAIRING” disappears.  
3D sound mode  
The volume is muted temporarily when pressing the (MUTE)  
button on the remote control. Press again to restore the volume.  
Wireless connection  
cannot be established.  
Makesurethereis noobstacles  
(especially metal) blocking  
between the sound bar and  
subwoofer.  
Manually re-link the sound bar  
and subwoofer (refer page 11).  
indicator turns blue.  
Periodically wipe the cabinet with a soft cloth.  
Caution:  
Do not use chemicals for cleaning (gasoline, paint  
thinner, etc.). It may damage the cabinet finish.  
Do not apply oil to the inside of each component. It may  
cause malfunctions.  
S+ 3D technology creates 3D sound through speakers  
regardless of the type of sound source, whether it is  
monaural, stereo or multichannel. It simulates sound  
transmission characteristics using digital signal processing  
to create a widening effect on the sound in the ambient  
space around the sound source.  
The AV SYNC level can be  
adjusted.  
Note:  
To increase the level, press  
the AV SYNC + button.  
General  
When the sound bar is turned off and back on again,  
muting is canceled.  
.....  
+3  
0
+1  
Sound Bar  
Subwoofer  
To decrease the level, press the AV SYNC – button.  
Symptom  
Possible cause  
Sound Bar  
Power source AC 120 V ~ 60 Hz  
Remote control  
Symptom  
No sound is heard.  
Is the input signal (selection)  
set properly?  
Sound Mode  
Power  
consumption  
38 W  
By using this technology, multichannel surround sound can  
be produced from 2.1ch source.  
Speaker output selection (HDMI connection)  
Error indicators and warnings  
PA  
IRING  
Press and hold  
(MUTE) button on the remote control  
Is the volume level set to “Min”?  
Is muting activated?  
Is HDMI compliant equipment  
being used?  
Sound bar operation:  
Possible cause  
Dimension  
Width: 37 - 1/16" (940 mm)  
Height: 2 - 7/8" (73 mm)  
Depth: 3 - 1/4" (83 mm)  
until “TV SPEAKER” or “SB SPEAKER” appears on the  
display to toggle sound output between this sound bar or  
TV.  
To change to a different mode, press the SOUND MODE  
button repeatedly until the desired sound mode is  
displayed.  
When you fail to perform operations properly, the following  
messages are displayed on the sound bar.  
Press the 3D AUDIO button repeatedly to select:  
The remote control does  
not operate properly.  
Is the battery polarity correct?  
Is the battery dead?  
Is the distance or angle  
incorrect?  
Are there any obstructions in  
front of the sound bar?  
Is there a strong light shining  
on the remote sensor?  
3D AUDIO 1 : Sound effect that emphasizes 3D  
sound.  
Notes:  
Weight  
7.27 lbs. (3.3 kg)  
Display  
Meaning  
Is the HDMI cable connected  
correctly?  
Remote control operation:  
Press the desired sound mode button on the remote  
control.  
If a device such as microwave oven, wireless LAN card,  
Bluetooth device or any other device that uses the  
same 2.4GHz frequency near the system, some sound  
interruption may be heard due to interference.  
The transmission distance of the wireless signal  
between the subwoofer and sound bar is about 32 feet  
(10 m), but may vary depending on your operating  
environment. If a steel-concrete or metallic wall is  
between the subwoofer and the sound bar, the system  
may not operate at all, because the wireless signal  
cannot penetrate metal.  
Output power RMS: Total 160 watts  
When there is no input signal.  
Play back the connected  
equipment.  
Nonstandard signal. Cannot  
be recognized.  
Signals other than DOLBY  
DIGITAL, DTS, Linear PCM  
cannot be recognized.  
Poor connection of the digital  
audio input terminal.  
Function  
Connect the HDMI cable  
correctly and then perform the  
reset procedure. (refer this  
page)  
Do not connect or disconnect  
an HDMI cable while power is  
on. This may lead to operation  
problems.  
RMS:  
Front Left/Right:  
80 watts per channel into 4 ohms at  
3D AUDIO 2 : Sound effect that maintains the 3D  
sound and improve vocal clarity.  
AUDIO IN  
HDMI 1 HDMI 2  
TV ARC  
OPTICAL  
CINEMA  
MUSIC  
GAME  
(for cinema sound effect)  
(for standard sound effect)  
(for game sound effect)  
(for sport broadcasting)  
(for news)  
1 kHz, 10% total harmonic distortion  
FTC:  
Is the remote control for  
another equipment used  
simultaneously?  
Front: (Left/Right):  
When pressing the SOURCE button, the input source will  
change. Press the SOURCE button repeatedly to select  
desired input source, or  
Minimum 50 watts per channel into  
4 ohms at 120 Hz to 20 kHz, 1% total  
harmonic distortion  
SPORT  
NEWS  
3D AUDIO OFF : 3D sound effect off.  
The sound bar cannot  
be turned on with the  
remote control.  
Is the AC power cord of the  
sound bar plugged in?  
press TV ARC button on the remote control to select TV ARC.  
(Display blinks)  
The sound from  
subwoofer is not well  
balanced.  
Is the subwoofer level set to the  
minimum or maximum level?  
Output  
terminal  
HDMI™ output: (audio/video support up  
to 1080p) x 1  
This product incorporates decoders supporting the Dolby  
Digital system and DTS system.  
Note:  
Is the battery inserted?  
Turn off the sound bar and  
check if the cable is  
connected properly.  
NIGHT  
BYPASS  
(for night)  
The backup function will protect the memorized function  
mode for a few hours should there be a power failure or the  
Input terminal Analog input (AUDIO IN): x 1  
500 mV / 47 kohms  
Caution:  
(for flat sound effect)  
Power turns off  
suddenly.  
Is the HDMI cable connected  
correctly? Connect the HDMI  
cable correctly and then  
DTS (Digital One of the digital audio systems for theatrical  
Condensation  
Keep the subwoofer away from water and moisture.  
AC power cord becomes disconnected.  
Theater  
Systems)  
use. As the sound quality is emphasized, you  
can enjoy the realistic sound effect in the home  
theater system.  
Optical digital input (OPTICAL):  
Square type x 1  
HDMI input: (audio/video support up to  
1080p) x 2  
When the protection circuit is  
activated.  
To get the optimum listening performance, make sure  
the area around the sound bar and subwoofer is clear  
of any obstacles.  
Sudden temperature changes, storage or operation in an extremely  
humid environment may cause condensation inside the cabinet or  
on the transmitter on the remote control. Condensation can cause  
the sound bar to malfunction. If this happens, leave the power on  
until normal playback is possible (about 1 hour). Wipe off any  
condensation on the transmitter with a soft cloth before operating the  
sound bar.  
Bass and Treble Control  
perform the reset procedure.  
APC (Auto Power Off Control)  
Demo indicator  
(blinks red)  
Noise is heard during  
playback.  
Move the speaker away from  
any computers or mobile  
phones.  
Lights up when detecting DTS signal.  
Bass and Treble control is applicable during BYPASS  
mode only.  
This sound bar can be set to turn off automatically if no signal is  
detected.  
1. Press the APC button repeatedly to select the time.  
Type  
2 Way speaker system  
2 -1/4" (5.7 cm) woofer  
1" (2.5 cm) Soft Dome  
Dolby Digital One of the digital audio systems for theatrical  
use. You can also enjoy the stereophonic effect  
in the home theater system.  
Display brightness control  
(*): Should the same message appear even if the speaker is  
unplugged and plugged in, or is set to the stand-by mode  
and on again, contact your local dealer where you  
purchased the sound bar.  
Bass Control  
1. Press the BASS button.  
2. Within 5 seconds, press the VOL (+ or –) button to adjust  
the bass.  
When a button is  
pressed, the sound bar  
does not respond.  
Set the sound bar to the stand-  
by mode and then turn it back  
on.  
Press the DIMMER button to adjust the brightness of the  
display.  
Maximum  
input power  
160 W  
APC 20 min  
APC 15 min  
Lights up when detecting Dolby Digital signal.  
PCM  
This is a general term for digitally encoded audio  
If problem occurs during operation  
Rated input  
power  
80 W  
Dimmer 1  
Dimmer 2  
Dimmer Off  
(
Display is dim  
(Display gets dimmer)  
Display is bright  
)
The power is not turned  
on.  
Is the sound bar unplugged?  
APC 5 min  
APC 10 min  
(Pulse Code signals on a CD or DVD.  
Modulation) This sound bar lets you enjoy playback of digital  
signals from sources such as CD or DVD.  
Treble Control  
The protection circuit may be  
activated. Unplug and plug in  
the power cord again after 5  
minutes or more.  
When this product is subject to strong external interference  
(mechanical shock, excessive static electricity, abnormal supply  
voltage due to lightning, etc.) or if it is operated incorrectly, it may  
malfunction.  
2. The sound bar will enter the power stand-by mode  
automatically if no signal is detected after the preset  
time has elapsed.  
Impedance  
4 ohms  
1. Press the TREBLE button.  
2. Within 5 seconds, press the VOL (+ or –) button to adjust  
the bass.  
Subwoofer  
(
)
Notes:  
3D imagesnotdisplayed  
on the TV.  
Depending on the TV and  
Video component, 3D images  
may not be displayed.  
If such a problem occurs, do the following:  
1. Set the sound bar to the stand-by mode and turn the power on  
again.  
2. If the sound bar is not restored in the previous operation, unplug  
and plug in the sound bar again, and then turn the power on.  
Power source AC 120 V ~ 60 Hz  
Operating the TV with the remote  
control  
You can operate Sharp TVs with this system’s remote  
control.  
APC (Auto Power Off Control) is only applicable for TV  
ARC, OPTICAL and AUDIO IN input function. It will not  
work for HDMI 1 or HDMI 2 input function.  
This system will automatically power off if TV or similar  
component which supports HDMI CEC is turned off.  
During OPTICAL input function, if you mute or pause  
the playback (depending on the connected  
Subwoofer level control  
Volume auto fade-in  
Power  
consumption  
33 W  
Check the operation manual of  
The subwoofer level can be  
adjusted.  
To increase the level, press  
the SW LEVEL  
To decrease the level, press the SW LEVEL  
If you turn off and on the sound bar with the volume set to  
80 or higher, the volume starts at 40 and fades in to the last  
set level.  
the respective component.  
HDMI cable not support 3D  
image.  
Output power RMS:  
150 watts per channel into 3 ohms at  
100 Hz, 10% total harmonic distortion  
FTC:  
Minimum 110 watts per channel into  
3 ohms at 100 Hz, 1% total harmonic  
distortion  
.....  
–5 –4  
+4 +5  
Watching TV  
button.  
Factory reset, clearing all memory  
Background noise  
appears when  
Please change to HDMI/ARC  
or headphone terminal from  
TV-Set/DVD/Blu-ray Disc  
Player. This effect may occur  
depending on TV/DVD/Blu-ray  
Disc Player-Brand, model and  
age, and it is not the sound bar  
problem.  
button.  
Volume control  
Make sure to disconnect all output and input cables attached to the  
sound bar before performing the factory reset.  
1. Press the ON/STAND-BY button to enter the power stand-by  
mode.  
2. While pressing the SOUND MODE button, press and hold the  
ON/STAND-BY button until “RESET” appears.  
Notes:  
component), APC function wll be activated. The system  
will turn off after the preset time has elapse.  
Point the remote control at the TV.  
connecting with RCA  
audio output terminal  
connection from a TV-  
set/ DVD/Blu-ray Disc  
Player.  
When sound from the speaker is distorted, decrease  
the subwoofer level.  
When changing the subwoofer level, the output level of  
the subwoofer is also changed.  
Sound bar operation:  
Press the VOLUME +  
button to increase the  
1 Press the TV ( ) ON/STAND-BY button to turn on  
the TV.  
Type  
Subwoofer system  
6 - 5/16" (16 cm) woofer  
Audio Return Channel (ARC) (Audio  
Return Channel submenu)  
The audio return channel (ARC) function enables an HDMI  
ARC-capable TV to send the audio stream to the HDMI OUT  
jack of the receiver. To use this function, you must select the  
TV ARC input and your TV must supports the ARC.  
2 Pressing the TV CH  
or  
button enables TV  
volume and the VOLUME –  
.....  
Max  
99  
Maximum  
300 W  
150 W  
3 ohms  
Min  
1
2
channelswitching.  
button for decreasing.  
input power  
3 Press the TV VOL + or – button to adjust the TV  
volume.  
Remote control operation:  
Press the VOL + button to increase the volume and the  
VOL – button to decrease the volume.  
Wireless connection  
cannot be established.  
Check the distance between  
the sound bar and subwoofer  
(less than 32 feet (10 m)).  
Make sure there is no other  
wireless devices near the unit.  
Rated input  
power  
Impedance  
Dimensions  
Other operable button  
Caution:  
Width: 5 - 11/16" (144 mm)  
Height: 16 - 15/16" (430 mm)  
Depth: 12 - 1/16" (306 mm)  
This operation will erase all data stored in memory.  
Input Select Button  
Weight  
13.42 lbs. (6.1 kg)  
E-12  
E-13  
E-14  
E-15  
 
HT-SB40_EN (A1).indd  
1
12/5/2012 8:49:44 AM  

Sennheiser Headphones RS 185 User Manual
SIIG Computer Drive 04 0265F User Manual
Sony Cordless Telephone SPP A2470 User Manual
Sony DVD Player DVP K370 User Manual
Sony Stereo System 4 183 777 121 User Manual
Sony TV Video Accessories 4 170 060 121 User Manual
SPX Cooling Technologies Humidifier Marley MS User Manual
Stamina Products Baby Gym 55 5686B User Manual
Star Micronics Printer NX 510 User Manual
Stinger Automobile Accessories SGN11 User Manual